Questions & Answers

Wiring diagram question 2014 Toyota Tacoma

0 votes
I've installed 4 or 5 of these evo-ones in multiple vehicles with a t-harnes. However I have a quick question on this 2014 Toyota Tacoma 4cyl w/ t-harness. I just want to make sure I'm reading the diagram correctly before I start.  Guide#19621.

 

On the IMI wire... when the wire is cut at the white ecm plug. Do both of the following wires go to the ecm side of the plug?

white/red D6 to the cut blue/white wire on Ecm plug side

lt blue A20 to the same blue/white on Ecm plug side

white/green D4 to the other cut end of the blue/white wire?

 

Then just splice the IMO wire..

lt blue/black A10 to green/black at ecm plug

 

Thanks
posté Juin 12, 2017 dans la catégorie Toyota par Lastminuteracin (650 points)

2 Réponses

+1 vote
 
Meilleure réponse
You got it!!

Twist them generously togheter and don't use solder...

Just twist and tape.
répondu Juin 12, 2017 par Charles Beauchamp (9,020 points)
élue Juin 12, 2017 par Lastminuteracin
Any reason not to solder them?? one more question... it also doesnt say to cut the loop for auto transmission on this diagram>>> Is that correct? I see on the other diagram without the t-harness it does say to cut it.Oh, and thank you for the clarification.
+1 vote
Solder can create noise/resistance in the line, So when dealing with data messages its usually just better to twist them together.

On a autmatic transmission vehicle you cut the yellow loop.
répondu Juin 12, 2017 par derek g (347,180 points)
Thanks. That's what I figured.
Having a small issue with the wiring diagram matching the vehicle. The imi and imo wires are not located in the correct pins according to the wire color or fortin evo-one diagram. This is a 2014 pre-runner 4cyl tacoma. According to all data it's the black connector on the next to bottom plug in the ecm pins 31&32. However that doesn't match either. I do have those two wires on pins 13&17 on a he black connector. Is  there and definitive way to test the data wires?
Anybody have any insight?
there are actually 2 ways for transponder bypass on this vehicle.

-- The T-harness guide shows IMI-IMO

-- The non t-harness guide shows IMMO Data at the OBD2.   (FYI, this type of install can still be done with the Tharness, the harness is to cover the ignition harness connections which are the same)   This type of 'bypass' using IMMO data is not functional on all models. It relies on heavily on if the specific vehicle ever had the option of having a Factory starter.

 

IMI-IMO can be tested with a logic probe. You would be looking for something to the effect of a few LED flashes on the probe. (test light would not work, multimeter can be too slow)

--- IMI will have something happen as soon as ignition is on

--- IMO will have something happen during crank.

 

Alldata definitly says pin 31-32 for the Tacoma PreRunner in a black at the ECM. The ECM placement seems to be different per different trim of the 4 runner (2WD, 4WD, engine type etc...)  I took some screen shots but the picture upload seems down right now...

I think I may just go the normal install route and incorporate the t-harness for the ignition wires. Hopefully that will work with this truck since I don't have a logic probe just a fluke meter.  I even pulled up the Toyota tech site and this truck doesn't match that either. Is it possible for a 2014 to not have an imobilizer? Either way I hope the standard wiring works using can high and low, lock and unlock. Thanks everyone for all the help!

I doubt there is no immobilizer but there is a really easy way to find.

 

Wrap plastic portion your key in aluminium foil and try starting your truck. If it starts, you have no immobilizer (or the key doesnt have enough foil). If it does not start, you have an immobilizer.

 

There should also be someking of dummy light i nthe cluster while ignition is first turned on indicating the car is equipped with an immobilizer.
I'll have to ask my buddy if it has a security light. I don't have the truck at the moment. I'm sure it has an imobilizer. I just don't understand why I can't find a diagram to match the truck. Makes absolutely no sense. I know I'm on the Ecm and the correct connector according to all the diagrams. I'm going to try the regular wiring next time I have the truck.  Probably should have went that route anyway
there are 2 modules in back of the goves box with a series of about 4 or 5 connectors on each.

- you want the module that is furthest to the right.

- the black connector is the 2nd from the bottom.

-----------

You can always try the other method with IMMO Data and CAN-HI, CAN-LO at the OBD2.

It's real easy. Connect the t-harness, connect the 3 connections at the OBD2, and try programming the module. Ignore all other connections for now.   https://cdn.fortin.ca/download/65191/evo-one_ig_reg_bi_toy-tacoma_gkey_2010-2015_a_65191.pdf
Yeah, I know where it's supposed to be located lol. I'll add a picture too when I get the truck again. I'm gonna try what you said. Thank you again. I'll be sure to update this when I have the chance to install it again
Truck does not have an immobilizer. Wrapped the key in multiple layers of foil and it still starts. The immobilizer light does not illuminate either when locked. Also in the toyota owners booklet it shows that the shape of the key we have the vehicle will not have an immobilizer. So i wonder if i can just hook up the CAN wires and program it on  the blue led..Since theres no immoblizer it will not program the way the guide says cause theres no imobilizer to get data from. Or should i just order something else??

Well that explains a lot!

You can program only can-bus but it's honestly not worth it as the only thing covered would be Tach detection.

 

Without requiring any programming (no CAN-Bus, no Immobilizer),

-- connect all wires except for the IMI-IMO and the CAN-BUS wires. (The Tharness, and brake input are the minimums)

-- Plug in the EVO without holding down any button. The three leds will flash simaltaneously for about 20 seconds.

-- Done. You can now program the RF-KIT.

 

If you really want to program the unit with only CAN-BUS, the programming is little different than what is said in the guide.

  1. Press and hold the programming button while inserting the 6-pin main harness.
  2. Release the button when the LED cycles to the BLUE LED
  3. Plug in remaining connectors.
  4. Turn ignition On.
  5. Blue LED will flash
  6. Turn ignition OFF
  7. done.

In both cases make sure to enable option 2.4 in the remote starter settings.

Option 20.2-Tachless will also be needed if not bothering with the CAN-BUs connections.

...